Friday, March 10, 2017

I Like Sectional Warp Beams!

You may not have heard me cheer late last week, but I know my near neighbors must have.  I have had a hard time the last couple of years, staying on task up in the studio.  Nobody's fault but my own, I usually have too many irons in the fire, and end up getting nothing done.  Anyway last week, I spent a couple of days concentrated on weaving off some long standing warps.

 One of them was on the loom a couple of years (8/4 blankets) and the other warp (8/2 towels), had been on a loom I had sold at least 3 years ago, and had finally gotten back on a loom last month.  It really did not take long to weave this second warp in plainweave, letting the stripes do the all the work.  I haven't finished or washed the fabric that came off the looms, once I get that done, I will post some pictures.

The "Burchard" loom from Berkley, California, is a 4 harness counterbalance loom, that has a wooden sectional warp beam.  One of the sectional rakes was in need of repair, so I took it on Tuesday so that Polly could take a look at it.  She is going to repair it for me,  and soon I will be putting on a new warp for Linen kitchen towels.  This will be a first for me,  but I have quite a bit of linen on hand, and I have to use it for something!

The Sears "Hearthside" loom (6 harness/ 6 treadles, jack loom) had the towel warp on it.   About a month ago, I purchased some used Leclerc sectional rakes that I thought would fit this loom.  Once I emptied the loom, I went to work putting on the new sectional rakes, which do indeed fit the back beam.  (I prefer sectional warp beams, for me it simplifies warping, especially for long warps.)





 It required a little drilling on my part, but I was up for it.  I also had to go get some bolts and wing nuts  that would fit through both the rake and the old beam boards to hold it all together.


 (They are always curious about what project I am getting into when I go into the hardware store.)






An hour or so later  the rakes were in place and I was ready to start winding spools of yarn to get the new warp loaded.









I have had this pile of partial cones forever.  I usually use it for weft, but I do have a shelf full of full cones as well.  (This is 12/3 white cotton, that I got years ago when I inherited the famous 100yd warps of the very same thread)  I thought that it would ease the clutter (in my mind and on the shelf) a bit if I could empty some of these cones first as I wound the warp spools.


When I was finished with the 24 white spools I had emptied all these cones.  There are a few more partial cones remaining, and you can be sure I will be using them first as I wind bobbins for weft, before I break into the full cones.

I also wound 16 spools of 8/4 in the color red, it will give me a lot of choices as I design the warp as I go.
















Oh the possibilities!



I had already wound the red and white sections that go down the center of this towel warp before I stopped to get this picture, so I had moved on to the all whited sections.

 Here is a picture of the Leclerc spool rake that holds 40 spools.  A couple of months ago, I got a deal on 40 Leclerc warping spools, and this is the first time I have been able to use them.  I don't think that this tension box is a Leclerc, but it works just the same.




I had to clamp a board to the bottom of the back beam so that the tension box will stay on.  An extra clamp here and there keeps everything in place as I wind each 1inch wide, 20yd section.


















I have wound 17 sections and I plan to add an additional 3 sections on each side of  what is already on the loom, that will give me a good 23 inches in width for  some very thirsty kitchen towels.

I have found a broken twill threading that was designed for this very same 6 harness, 6 treadle  Hearthside loom.  It was on one of my favorite online resources,  here .  It is a wonderful website full of really old out of print and out of copyright books, magazines, articles etc , on any fiber related subject you can think of.


Spring break is right around the corner, which means more Grandma time for me in the coming 2 weeks, including a trip to Washington DC!  So it may be a couple of weeks before I can get back to this project, but you can be sure that I am looking forward to it!




I almost forgot, this week I finished the first band using Knit Picks "Curio" crochet cotton, that I posted about last week.  I really like how it turned out, it feels sturdy but soft in my hand and there is a slight sheen that "Curio" has that enhances this band.  There is also just the right amount of slickness to this yarn that makes "pulling the weft through on the succeeding shed" easier for me.  All in all I really recommend this yarn for all your warp faced band weaving needs.


That is it for today, Until next time, Happy Weaving!

Edit: because of math!


4 comments:

LA said...

I am so glad those rakes are doing the job for you!

Theresa said...

Congrats on the rakes. I had the sectional set up on the Delta loom, couldn't stand it, but then again, weaving long yardage isn't my focus. Know it makes life much easier for those that do!

runtmms said...

Looks great. I'm interested in the Leclerc sectional rakes. Can you tell me their total height - bottom of wood base to top of metal loop?

pittypats said...

I just purchased a 1980 Norwood Sectional beam loom, it came with a tension box that looks just like yours. I have no idea of the brand name have you found out the brand of yours? My tensioner does not have a counter on it, I am curious how the counter works and looks on yours, could you share another pic?.